SMC Networks SMC7004BR Manuel d'utilisateur Page 1

EZ Cable/DSL RouterSMC7004BRUser GuideThe information furnished by SMC Networks, Inc. (SMC) is believed to be accurate andreliable. However, no respo

-9-Figure 2-6 Setup of WAN and Printer connections for this product.4. Power on:Connect the power cord to power inlet and turn the power switch on. T

-10-Chapter 3 Network Settings and Software InstallationTo use the SMC7004BR correctly, you must properly configure the network settings of yourcompu

-11-Request timed out.there has been an error in your installation procedure. Please go through the followingchecklist to ensure proper installation:1

-12-Step 2: Click on the INSTALL button. Wait for the following Welcome dialog to appear,and click on the Next button.Step 3: Select the destination f

-13-Step 4: When the following window is displayed, click on the Finish button.Step 5: Select the item to restart the computer and then click the OK b

-14-Chapter 4 Configuring the SMC7004BRThis product provides a Web-based configuration scheme, which is configurable byNetscape Communicator or Inter

-15-4.2 StatusThis option provides the function for observing the product’ s operating status:A. WAN Port Status.If the WAN port is assigned a dynamic

-16-4.3 ToolboxThis option enables you to change the administrator password. Also, you can obtaininformation about Firmware version and WAN's MAC

-17-4.4 Primary SetupThis option enables the product to work properly. The setting items and the web appearancedepend on the type of WAN. Choose the c

-18-4.4.1 Static IP AddressWAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the propersetting value provided by your ISP.4.4.2 D

-1-Trademarks:SMC is a registered trademark; and SMC7004BR is a registered trademark of SMC Networks, Inc.Other products and company names are tradema

-19-4.5 DHCP ServerThe settings of the TCP/IP environment include Host IP, Subnet Mask, Gateway, and DNSconfigurations. It is not easy to correctly co

-20-4.6 Virtual ServerThe SMC7004BR’ s NAT (Network Address Translation) firewall filters out unrecognizedpackets to protect your Intranet, so all hos

-21-192.168.123.2, and a PPTP VPN server at 192.168.123.6, you need to specify the followingvirtual server mapping table:Service Port Server IP Enable

-22-4.7 Special APSome applications require multiple connections, such as Internet games, videoconferencing, Internet telephony and others. Due to the

-23-4.8 Access ControlAccess Control allows you to assign the access right for each user. First, you must divideusers into different groups, as identi

-24-4.9 Miscellaneous Items1. IP Address of DMZ Host: The DMZ (Demilitarized Zone) Host is a host without theprotection of a firewall. It allows a com

-25-Chapter 5 Print ServerThe SMC7004BR provides the function of a network print server for MS Windows95/98/NT and Unix based platforms.5.1 Configuri

-26-2. Click the Details item:3. Choose the “PRTmate: (All-in-1)” from the list attached under the Print To item. Besure that the Printer Driver item

-27-printer.4. Click the Port Settings button:Type in the IP address of this product and then click the OK button.5. Make sure that all the settings m

-28-Compared to the procedure in the last section, the selection of Details is equivalent to theselection of Ports, and Port Settings is equivalent to

-2-Table of ContentsChapter 1 Introduction...

-29-Appendix A: Console ModeWhen you forget the system password or the IP address for this product, you need to enterthe console mode to reset them.B

-30-Appendix B: TCP/IP Configuration for Windows 95/98This section will show you how to install the TCP/IP protocol into your personal computer.If yo

-31-6. The TCP/IP protocol will be listed in the Network window. Click OK to complete theinstall procedure and restart your PC to enable the TCP/IP pr

-32-4. You have now two setting methods:A. obtain IP via DHCP servera. Select Obtain an IP address automatically in the IP Address tab.b. Don’ t input

-33-c. Choose Disable DNS in the DNS Configuration tab.B. Configure the IP manuallya. Select Specify an IP address in the IP Address tab. The default

-34-b. In the Gateway tab, add the IP address of this product (default IP is192.168.123.254) in the New gateway field and click Add button.c. In the D

-35-Appendix C: Installation Guide For Specific ISPThe WAN types provided by SMC7004BR will cover almost all types of ISP services.Some ISPs, however

-36-C.2 MediaOne1. Be sure you have a computer that is already set up to access MediaOne and that theMAC address of the Ethernet adapter used in this

-3-Appendix A: Console Mode... 29Appendix B: TCP/IP Co

-4-Chapter 1 IntroductionCongratulations on your purchase of the SMC7004BR. This product is specificallydesigned for small office and home office nee

-5-- configurable through any networked computer’ s web browser using Netscape orInternet Explorer.l Access Control supported- allows you to assign di

-6-Chapter 2 Hardware Installation2.1. Panel Layout2.1.1. Front PanelFigure 2-1 Front Panel1 - 4 LAN port socket (RJ-45). These are where you will co

-7-2.1.3. Top PanelFigure 2-3 Top PanelLAN Port 1-4 LAN port indicators, Green. The LED flashes when the LAN port issending or receiving data.WAN WAN

-8-l Place product on a flat horizontal plane.l Keep product away from any heating devices.l Do not place product in a dusty or wet environment.The re