SMC Networks SMC9452TX Manuel d'utilisateur

EZ Card 10001000 Mbps Gigabit Ethernet PCI Network CardHigh performance for instant access to network resourcesDelivers 2 Gbps of bandwidth over insta

COMPLIANCESvi

viiTABLE OF CONTENTS1 Installing The Network Card . . . . . . . . . . . . . . . 1-1Introduction . . . . . . . . . . . . . . . . . . . . . . . . .

viiiOffload Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2Packet Size (Maximum) . . . . . . . . . . . . . . . . . . . . . . .

1-1CHAPTER 1INSTALLING THE NETWORK CARDIntroductionSMC’s EZ Card 1000, SMC9452TX, is a Gigabit Ethernet network interface card for 32-bit PCI local bu

INSTALLING THE NETWORK CARD1-2Hardware DescriptionThe EZ Card 1000 is a Gigabit Ethernet network card designed for 32-bit PCI-bus computers. The card

INSTALLING THE NETWORK CARD1-3LED IndicatorsThe EZ Card 1000 network card includes status LED indicators as described in the following figure and tabl

INSTALLING THE NETWORK CARD1-4Package ContentsAfter unpacking the EZ Card 1000, check the contents of the box to be sure you have received the followi

INSTALLING THE NETWORK CARD1-5System RequirementsBefore you install the EZ Card 1000, check your system for the following requirements:◆ A PC and BIOS

INSTALLING THE NETWORK CARD1-6• When using a 32-bit PCI slot, the end of the card’s edge connector will be exposed. Be careful that it does not touch

INSTALLING THE NETWORK CARD1-74. Replace the chassis cover on your PC and power it on. 5. The EZ Card 1000 should be automatically configured by the h

INSTALLING THE NETWORK CARD1-8Connecting Category 5 CableTo connect to a 1000BASE-T Gigabit Ethernet device, use the RJ-45 connector on the network ca

INSTALLING THE NETWORK CARD1-9Connecting UTP Cable1. Attach the male RJ-45 connector on one end of a UTP cable to the network card’s RJ-45 port.Figure

INSTALLING THE NETWORK CARD1-10

2-1CHAPTER 2INSTALLING AND CONFIGURINGNETWORK DRIVERSWindows NT 4.0 InstallationCaution: Prior to installing the driver, make sure you have upgraded t

INSTALLING AND CONFIGURING NETWORK DRIVERS2-24. When prompted to “Select a Network Adapter,” click on “Have Disk.” Insert the SuperDisk when prompted

INSTALLING AND CONFIGURING NETWORK DRIVERS2-3Secondary InstallationFollow this procedure if you have already installed another network card or loaded

INSTALLING AND CONFIGURING NETWORK DRIVERS2-4Further ConfigurationYou can modify card settings, install additional protocols and other network compone

INSTALLING AND CONFIGURING NETWORK DRIVERS2-5Windows 2000 InstallationThe EZ Card 1000 driver for Windows 2000 conforms to the Network Driver Interfac

INSTALLING AND CONFIGURING NETWORK DRIVERS2-6Novell NetWare InstallationNetWare Server 5.0Installing the LAN driver is part of the NetWare installatio

INSTALLING AND CONFIGURING NETWORK DRIVERS2-78. A screen with three dialog boxes is displayed. To change the driver configuration, tab to the “SMC9452

6 HughesIrvine, CA 92618Phone: (949) 707-2400EZ Card 1000User GuideFrom SMC’s EZ line of low-cost workgroup LAN solutionsJune 2001Pub. # 150000003500A

INSTALLING AND CONFIGURING NETWORK DRIVERS2-8NetWare Server 4.11Installing the LAN driver is part of the NetWare installation process. Use the followi

INSTALLING AND CONFIGURING NETWORK DRIVERS2-99. A screen with three dialog boxes is displayed. To change the driver configuration, tab to the “SMC9452

INSTALLING AND CONFIGURING NETWORK DRIVERS2-10Linux 2.2.X or Later InstallationThis section describes the procedure for manual and automatic loading a

INSTALLING AND CONFIGURING NETWORK DRIVERS2-11RxBufSize: This is the size of the receive buffer memory space allocated per receive descriptor (the lab

INSTALLING AND CONFIGURING NETWORK DRIVERS2-12BOOTPROTO=noneBROADCAST=207.200.5.255NETWORK=207.200.5.0NETMASK=255.255.255.0IPADDR=207.200.5.2Automatic

INSTALLING AND CONFIGURING NETWORK DRIVERS2-13where “ethx” will be “eth0” if you do not have any other adapters, “eth1” if you already have one, and s

INSTALLING AND CONFIGURING NETWORK DRIVERS2-14Windows 98 InstallationThe EZ Card 1000 driver for Windows 98 conforms to the Network Driver Interface S

INSTALLING AND CONFIGURING NETWORK DRIVERS2-15“C:\WINDOWS\SYSTEM” directory and the “SMC9452.INF” file from “A:\Win98” to the “C:\WINDOWS\INF” directo

INSTALLING AND CONFIGURING NETWORK DRIVERS2-16Other InstallationsRefer to the installation documents on SMC’s SuperDisk for instructions on installing

3-1CHAPTER 3CONFIGURING THENETWORK CARDConfigurationThis section describes the configuration procedure in a Windows environment. When you install the

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, n

CONFIGURING THE NETWORK CARD3-2Media TypeIn this field auto-negotiation can be enabled, or the card’s link speed and duplex mode can be selected. If a

CONFIGURING THE NETWORK CARD3-3Pause ControlPause frames are used to control network congestion. In this field the card may be configured to transmit

CONFIGURING THE NETWORK CARD3-4Using VLANsThe TigerCard 1000 network card supports the IEEE 802.1Q VLAN standard and can be configured to participate

A-1APPENDIX ATROUBLESHOOTINGPCI CompatibilityEarly PCI BIOS versions do not properly support the PCI specification and may “hang” when a network card

TROUBLESHOOTINGA-2◆ Make sure the PCI slot is configured to support INTA.◆ Ensure that INTA for the slot is assigned to a free interrupt (IRQ) number.

TROUBLESHOOTINGA-3Solutions for Common ProblemsProblems are often caused by cabling errors, conflicts with other devices installed in the same compute

TROUBLESHOOTINGA-4Network Connection ProblemsIf your computer cannot find the EZ Card 1000 card, or the network driver does not install correctly, che

B-1APPENDIX BCABLESCable Specifications Cable Types and SpecificationsCable Type Max. Length Connector10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft)

CABLESB-2Twisted-Pair Cable and Pin AssignmentsCaution: DO NOT plug a phone jack connector into any RJ-45 port. Use only twisted-pair cables with RJ-4

CABLESB-31000BASE-T Pin Assignments1000BASE-T ports support automatic MDI/MDI-X operation, so you can use straight-through cables for all network con

iLimited WarrantyLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un

CABLESB-4

C-1APPENDIX CSPECIFICATIONSBus Interface32-bit bus master, PCI33 MHz and 66 MHzInterruptINTANetwork Interface1000BASE-T: UTP cable; Category 5, 5e or

SPECIFICATIONSC-2Operating Voltage+5 VDC @ 2.7 A maximumSize (without bracket)7.9 x 16.5 cm (3.11 x 6.50 in.)Weight80g (2.8 oz)TemperatureOperating 0

SPECIFICATIONSC-3Software DriversODI Drivers NetWare Server 4.1x or laterNDIS Drivers Windows NT 4.0Windows 95Windows 98Windows MEWindows 2000Unix Dri

SPECIFICATIONSC-4

Glossary-1GLOSSARY10BASE-TIEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable.100BASE-TXIEEE 802.3u specific

GLOSSARYGlossary-2End StationA workstation, server, switch, bridge or router.EthernetA network communication system developed and standardized by DEC,

GLOSSARYGlossary-3IEEE 802.3Defines carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications.

GLOSSARYGlossary-4Network DiameterWire distance between two end stations in the same collision domain.Switched PortsPorts that are on separate collisi

Index-1Aauto-negotiation 2-2BBIOS requirements 1-5, A-1bus-mastering 1-5, A-1Ccableadjusting Category 5 cable 1-8guidelines 1-7specifications B-1card

LIMITED WARRANTYiiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY SHALL BE REPAIR OR REPLACEM

INDEXIndex-2PCIbus specification 1-5compatibility A-1configuration 1-7pin assignments B-2RRELEASE.TXT file 1-7requirements of system 1-5RJ-45 connecto

6 HughesIrvine, CA 92618Phone: (949) 707-2400FOR TECHNICAL SUPPORT, CALL:From U.S.A. and Canada (24 hours, 7 days a week)(800) SMC-4-YOU; (949) 707-24

iiiCOMPLIANCESFCC - Class BThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

COMPLIANCESivEC Conformance Declaration - Class BSMC contact for these products in Europe is:SMC Networks Europe,Edificio Conata II, Calle Fructuós Ge

COMPLIANCESvIndustry Canada - Class BThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set